Honda GX160 T2 QTN 4-Strokes Petrol Engine 

Honda GX160 T2 QTN 4-Strokes Petrol Engine 

Max Horsepower : 5.5 hp/4000 rpm

Features :

E

4-stroke gasoline engine over the piston

Cylinder capacity 163 cc

Good fuel economy.

1 year full engine warranty

Weight: 15000 g

COMMON APPLICATIONS (HONDA GX160 suitable for?)

Pressure washers  

Commercial lawn and garden equipment  

Tillers / cultivators  

Generators 

Construction / industrial equipment  

Agricultural equipment  

Water pumps  

     Components and controls

     of the engine

Oil warning system (Available models only)

The oil level warning system is designed to prevent damage to the engine due to insufficient oil in the oil tank.

When the oil level in the oil sump lower than the safe level. Oil level warning light Automatic engine oil level warning system.

(Even if the switch is still in the open position) If the engine stops and can not start Check the oil level. The problem solved in another part.

Circuit breaker (Available models only)

This cover protects the battery circuit. When the short circuit occurs The polarity of the battery will cause the circuit breaker to work.

The position shown in green inside the circuit breaker is pushed out to indicate that the circuit breaker has stopped. If this is the case, check the cause. And fix it before resetting the circuit protection. Press the circuit breaker button to reset.

HONDA GX160 4-stroke petrol engine

For safety Avoid using engines in areas where there is no air flow, such as a garage. It contains carbon monoxide, which is a substance.

It can spread quickly in airy areas. This may cause serious injury or illness.

Starting the engine of 4-stroke gasoline engine HONDA GX160.

1. Move the fuel tank lever to the open position. Turn "ON"

2. When the engine is cold. Slide the shif to the closed position. "CLOSED"

When the engine is re-heated. Release the shoe to the lower position. Open "OPEN"

For some types of engines. The shocks are used more than the shock absorber with the engine as shown. Please refer to the manufacturer's instructions.

3. Lower the accelerator pedal from the lower idle (MIN) by about 1/3 of the lower throttle (MAX).

For some types of engines. The acceleration kit is more remote than the accelerator fitted with the engine as shown. Please refer to the manufacturer's instructions.

4. Slide the switch to the ON position.

5.Starts

Coil starter

Pull the handle lightly. I feel that resistance. Then pull up quickly. In the direction of the arrows shown below. Let's start with a slow start.

Electric motor (Available models only)

Twist the engine switch to the starting position and hold it until it clicks. If the engine does not start within 5 seconds, release the switch and turn it on for 10 seconds.

Start again When the engine is plugged in, release the switch to the "ON" position.

6. If the shoe is pulled to the closed position CLOSED to start the engine, gently push the shoe to the open position. OPEN when the engine starts to warm.

Engine shutdown

Emergency power outage Turn the power switch to OFF. Use the following steps.

1. Slide the accelerator to the MINUTE position.

Application of the engine sometimes. It uses remote control over the accelerator that is fitted to the engine.

2. Move the engine to the OFF position.

3. Move the fuel tank to the OFF position. OFF

Engine speed adjustment

Move the accelerator to the required speed.

For some types of engines. It uses a remote control unit rather than a throttle fitted with the engine as shown.

Oil level check

Check engine oil level while engine is running. And low level.

1. Open the torque wrench / oil level gauge. And wipe it clean.

2. Wear the oil level cap / cap without screwing it to the oil filler mouth. Or lower than the bottom of the oil level gauge.

Introduce the recommended lubricant. To top up. (Bottom of the oil fill hole) Do not overfill.

4. Close the oil / oil lever.

Oil change

Oil warning system (Only available models) will automatically turn off the engine. Before the oil is lower than the safe level.

Always check the oil level before starting. To prevent engine outages.

Oil change

Oil Spill The machine is still hot because it will make oil out easier.

1. Place the appropriate container under the engine. To use the oil, then remove the oil level cap / shaft.

Oil and oil screws removed.

2. Let the oil run out. Then, make sure the coil is reheated. And back around the new band. And tighten the engine oil.

3. Lower the engine's horizontal position, add the recommended oil to the top. (Bottom of oil fill hole)

4. Close the oil cap / shaft back in. Rotate tightly.

Cleaning

Two-Tier Filter System

1. Remove the plug from the filter cap. And remove the cover.

2. Remove the cap from the air filter and remove the air filter.

3. Remove the foam filter from the paper air filter.

4. Check both types of air filters. If it is damaged, change it. Should replace the filter according to the maintenance schedule.

5. Clean the air filter if you need to re-use it.

6. Wind turbine only.

7. Wipe the dirt off the filter housing and the cover. Use a clean towel to keep the dirt out of the casing.

Which is the entrance to the carburetor.

8. Place the foam filter over the air filter. And install the filter to the assembly. Make sure that the gasket is placed under the air filter.

Then tighten the bolt nut.

9. Put the filter cover and lock the cover firmly.

Oil Filter (Wet)

1. Remove the tail nut. Air filter cover and cover

2. Remove the air filter from the cover, wash the cover and filter with warm soapy water, shake and let dry. Or clean with non-flammable solvents and let dry.

3. dip filter air cleaner And squeeze excess oil. If there is too much oil in the filter sponge. The engine is very smoke.

4. Remove the oil from the air filter. Clean with non-flammable and dry solvents.

5. Refill the air filter to the oil level mark. Use the same oil as recommended oil. Oil Capacity: 60 cubic centimeters

6. Assemble the air filter back. And tighten the nut tight.

Cleaning And check the sparks.

1. Use a scrub brush, charcoal powder, charcoal grate, grill, spark protector. Be careful not to damage the grill. Replace the spark plugs if they break or break.

2. Combination of sparks. Exhaust pipe, tailgate and exhaust pipe retractors.

3. Air filter assembly

Replacing fuses (Available models only)

Circuit Starter Kit Including the battery circuit. The fuse is protected if the fuse is defective. Electric starter will not work. Even if the fuse is broken, but still can.

Can be manually operated. But the engine will not charge the battery.

1. Remove the 6x12 mm screws from the back cover of the machine switch box. And remove the cover.

2. Remove the fuse cover. To check the fuse

** If the fuse is broken Pull the fuse away. Replace the same sized fuse. Close the cover **

3. Clear the back cover. And tighten the special screws 6x12 mm to tighten.

HONDA GX160 four-stroke gasoline engine wiring diagram

Both oil level warning. Electric starter And controllers

Oil level warning Electric starter No circuit control

Oil level warning No circuit control